Publications with 50-74 Citations
Total: 22 papers.
Baik, S., Fowler, D.E., Blakely, J.M. & Raj, R. 1985, "Segregation of mg to the (0001) Surface of Doped Sapphire", Journal of the American Ceramic Society, vol. 68, no. 5, pp. 281-286.
Bampton, C.C., Mahoney, M.W., Hamilton, C.H., Ghosh, A.K. & Raj, R. 1983, "Control of Superplastic Cavitation by Hydrostatic-Pressure", Metallurgical Transactions A-Physical Metallurgy and Materials Science, vol. 14, no. 8, pp. 1583-1591.
Bampton, C.C. & Raj, R. 1982, "Influence of Hydrostatic-Pressure and Multiaxial Straining on Cavitation in a Superplastic Aluminum-Alloy", Acta Metallurgica, vol. 30, no. 11, pp. 2043-2053.
Bordia, R.K. & Raj, R. 1988, "Sintering of Tio2-Al2o3 Composites - a Model Experimental Investigation", Journal of the American Ceramic Society, vol. 71, no. 4, pp. 302-310.
Cheng, T.N. & Raj, R. 1989, "Flaw Generation during Constrained Sintering of Metal-Ceramic and Metal Glass Multilayer Films", Journal of the American Ceramic Society, vol. 72, no. 9, pp. 1649-1655.
Hsu, W.Y. & Raj, R. 1992, "Mgo Epitaxial Thin-Films on (100) Gaas as a Substrate for the Growth of Oriented Pbtio3", Applied Physics Letters, vol. 60, no. 25, pp. 3105-3107.
Liew, L.A., Liu, Y.P., Luo, R.L., Cross, T., An, L.N., Bright, V.M., Dunn, M.L., Daily, J.W. & Raj, R. 2002, "Fabrication of SiCN MEMS by photopolymerization of pre-ceramic polymer?", Sensors and Actuators A-Physical, vol. 95, no. 2-3, pp. 120-134.
Liew, L.A., Zhang, W.G., Bright, V.M., An, L.N., Dunn, M.L. & Raj, R. 2001, "Fabrication of SiCN ceramic MEMS using injectable polymer-precursor technique", Sensors and Actuators A-Physical, vol. 89, no. 1-2, pp. 64-70.
Lim, L.C. & Raj, R. 1984, "Effect of Boundary Structure on Slip-Induced Cavitation in Polycrystalline Nickel", Acta Metallurgica, vol. 32, no. 8, pp. 1183-1190.
Lim, L.C. & Raj, R. 1984, "On the Distribution of Sigma for Grain-Boundaries in Polycrystalline Nickel Prepared by Strain-Annealing Technique", Acta Metallurgica, vol. 32, no. 8, pp. 1177-1181.
Panda, P.C., Raj, R. & Morgan, P.E.D. 1985, "Superplastic Deformation in Fine-Grained Mgo.2al2o3 Spinel", Journal of the American Ceramic Society, vol. 68, no. 10, pp. 522-529.
Pavinich, W. & Raj, R. 1977, "Fracture at Elevated-Temperature", Metallurgical Transactions A-Physical Metallurgy and Materials Science, vol. 8, no. 12, pp. 1917-1933.
Phoenix, S.L. & Raj, R. 1992, "Scalings in Fracture Probabilities for a Brittle Matrix Fiber Composite", Acta Metallurgica Et Materialia, vol. 40, no. 11, pp. 2813-2828.
Raj, R. 1982, "Separation of Cavitation-Strain and Creep-Strain during Deformation", Journal of the American Ceramic Society, vol. 65, no. 3, pp. C46-C46.
Raj, R. 1981, "Morphology and Stability of the Glass Phase in Glass-Ceramic Systems", Journal of the American Ceramic Society, vol. 64, no. 5, pp. 245-248.
Raj, R. 1978, "Intergranular Fracture in Bicrystals", Acta Metallurgica, vol. 26, no. 2, pp. 341-349.
Raj, R. & Ghosh, A.K. 1981, "Micromechanical Modeling of Creep using Distributed Parameters", Acta Metallurgica, vol. 29, no. 2, pp. 283-292.
Raj, R. & Morgan, P.E.D. 1981, "Activation-Energies for Densification, Creep, and Grain-Boundary Sliding in Nitrogen Ceramics", Journal of the American Ceramic Society, vol. 64, no. 10, pp. C143-C145.
Raj, R., Riedel, R. & Soraru, G.D. 2001, "Introduction to the special topical issue on ultrahigh-temperature polymer-derived ceramics", Journal of the American Ceramic Society, vol. 84, no. 10, pp. 2158-2159.
Shieu, F.S., Raj, R. & Sass, S.L. 1990, "Control of the Mechanical-Properties of Metal Ceramic Interfaces through Interfacial Reactions", Acta Metallurgica Et Materialia, vol. 38, no. 11, pp. 2215-2224.
Tsai, R.L. & Raj, R. 1980, "The Role of Grain-Boundary Sliding in Fracture of Hot-Pressed Si3n4 at High-Temperatures", Journal of the American Ceramic Society, vol. 63, no. 9-10, pp. 513-517.
Wang, J.D. & Raj, R. 1991, "Activation-Energy for the Sintering of 2-Phase Alumina Zirconia Ceramics", Journal of the American Ceramic Society, vol. 74, no. 8, pp. 1959-1963.